Jun 11, 2010 Plug off the mains. To start viewing messages, select the forum that you want to visit from the selection below. I am a mechanic by trade and am more than confident of repairing the machine myself for the price of a couple of bearings and a couple of hours of my time, the only prob is that if I dismantle it and get stuck, I cant afford the time for it to be off the road as the cheese and kisses will kill me if she doesn't have a working machine. Remove the plastic clip holding it to the pump unit and then the metal cir clip holding it to the main drum. We also use content hosted by third-parties, such as YouTube, to provide relevant content. I'm trying to locate the knocking when the washing machine is on the spin cycle, I would like an expolded view of the machine and possible solution to the noise. You will find a lot of junk here, clean out thoroughly.
. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. Is the value of the pump about 200Ω? The filter is inside the big black rubber hose attached between the pump and the main drum. You can read more about the tracking technologies we use in our. The link below provides the detailed troubleshooting procedure of this error code.
Does the bowl wobble violently when spin starts? Turn the knob to off and on again and away it goes. If the strike is good, replace the door lock. Re-fit the lid and test the machine. On this basis, the machine has not done a lot of work, however over the last 2 months the drum has developed a lot of banging noise and vibration during the start and wing down of the Spin cycle. Please do the following: - Clean the filter, by removing the drain filter compartment Lid Found Left lower area of the front of the Washing Machine , then draining any excess water, afterwards turn the cap anti-clockwise to remove it.
This machine is about 4. During the Warranty Period Electrolux or its Authorised in relation to the Appliance or any services supplied by Electrolux. Let me know the answer if you can. We would really like to try to assist you. Electrolux should be able to tell you the error code over the phone, should the problem be related to the electronic board. The alarm sequence continues as long as the two buttons are held down. Not this time, thought this site may be helpful but it looks like Electrolux never answer any question put to them.
What doesn't make sense is the thing works mostly. First drain out all your water by lowering the exit hose into a bucket or drain. Dado Aug 24, 2015 Family error code E40 is visible to customers and could be E41,E42,E43,E44 and E45 only visible in service mode means problem with open door or door interlock. Anyone else had this problem? You can then slide the pump out of the filter housing. Inside the big flexible tube coming from the tub bottom is the filter, be prepared to find all sorts of junk here, clean out. So far happy with Samsung bubble wash. Keep putting it on drain till you get the water out or simply lower the drain hose into a wash basin.
This could be a normal clogged Drain Filter or worse maybe a faulty drain motor. If no blockage, you'll need to take the pump out and check that too. Any info would be accepted gratefully. As fro the tear, I'd try this: Ensure that everything is drier than a baby's bum, kinda like the Sahara on a hot day, then fill the tear with silastic or other rubber sealant. It seems to be from pulling out the hose at the bottom next to it. If you have broken wires in the wiring harness, replace the wiring.
The alarm sequence continues as long as the two buttons are held down. Jun 26, 2008 Hi Helenw, The error message E20, simply means the filter plastic cage which is located behind the trap door bottom right side of the machine is full and needs to be cleaned out. The pump needs to be checked. It needs to be cleaned. My wife says she has been having arm to arm combat for the past 18 months with Error 90 always showing.
While I am asking questions, do the pistons that support the drum need maintennance? The filter and drain pump are getting blocked in your machine. Also have the banging noise when it wants to spin but cuts out. Kind Regards David Marsh Jun 19, 2007. You can now take the drain hose off of the pump and take it out of the appliance to check for a blockage. The E42 error indicates a problem with the door lock mechanism. All the fibres and lint gets trapped in here and prevents the waste water from escaping, hence Error code E20.
Drain out all the water. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. We look forward to hearing from you soon. If the sent me a card, I could replace it myself, but do you think they will. I'd probably glue a tyre patch or the like over it too.
When it gets up to top speed it operates normally. If the door was closed, did you hear the lock attempt to engage? Also check for any small cloth getting blocked in the machine inside. Are there any suggestions of where I should look first? We've had this unit for a number of years, and its never missed a beat, until recently, it now makes a horrible noise when in operation - it's at it's loudest on spin - like the bearings have failed. Once it's empty, put a couple of towels down, unplug the machine and lay it carefully onto it's left side. In addition, replace the drain pump after having found no problem with the drain hose, cleaned the filter, and checked the drain pump impeller but the drain pump just hums, buzzes or whirs. Off course without a manual on-line Electrolux I can't fix the error.