Suzuki jimny sn413 2004 repair service manual. Suzuki Jimny / Samurai 2019-03-18

Suzuki jimny sn413 2004 repair service manual Rating: 5,6/10 611 reviews

Suzuki Jimny Workshop & Owners Manual

suzuki jimny sn413 2004 repair service manual

Then tighten them by the following numerical order in figure. Special tool A : 09900-06108 2 Apply penetrate lubricant between bearing race outer diame- ter and shaft yoke bore. Thus open refriger- ant container valve 4 to purge the charging line. When removal is necessary, use bearing puller to remove end housing bearing 1. Spring and rod assembly 7. Cooling System Component 15 N·m 1.

Next

Suzuki Jimny / Samurai

suzuki jimny sn413 2004 repair service manual

Three or two brake pipes are connected to the master cylin- der and they make two independent circuits. They are specifically written for the do-it-yourselfer as well as the experienced mechanic. Table of Contents General vehicle information Maintenance, body and chassis sheet metal panel Paint Body equipment Heating, ventilation and air conditioning Front wheel suspension Rear wheel suspension Wheels and tyres Brakes Engine Clutch Transmission Fuel and exhaust Steering Electrical equipment and instruments Accessories Best Manuals service manual 2014-07-17. Power steering pressure switch 39. If any malcondition is found, replace. Use of any other fluid is strictly prohibited.

Next

DOWNLOAD SUZUKI SERVICE MANUAL: SUZUKI JIMNY SN413 WORKSHOP SERVICE REPAIR MANUAL

suzuki jimny sn413 2004 repair service manual

Vehicle balance on hoist may change depending on what part to be removed. To install oil seal, use special tool Bearing installer. Following procedure also applies to cars with voltmeter and ammeter. Ignition coil assembly for No. Special tool A : 09917-68221 Tightening torque Crankshaft pulley bolt a : 150 N·m 15.

Next

DOWNLOAD SUZUKI SERVICE MANUAL: SUZUKI JIMNY SN413 WORKSHOP SERVICE REPAIR MANUAL

suzuki jimny sn413 2004 repair service manual

Accordingly, when any internal engine parts are serviced, care and cleanliness are important. Measure cylinder head bore and tappet outside diameter to deter- mine cylinder head-to-tappet clearance. Right rear tire Engine Identification Number The number is punched on the cylinder block. Fill and maintain brake fluid level in reservoir. Do not allow brake fluid to get on painted surface.

Next

SUZUKI JIMNY SERVICE MANUAL Pdf Download.

suzuki jimny sn413 2004 repair service manual

Intermittent trouble or Go to Step 5. Dual pressure switch C: Superheated vapor 3. Disc in badly damaged condition must be replaced. Fastener Strength Identification Most commonly used metric fastener strength property classes are 4T, 6. A : Piston diameter as measured. When replacing any fasteners, it is most impor- tant that replacement fasteners be the correct diameter, thread pitch and strength.

Next

Suzuki Jimny / Samurai

suzuki jimny sn413 2004 repair service manual

Engine hook Do not reuse. Repair or replace defective parts, if any. Camshaft 9 Install camshaft housing 1 and tighten them to specified torque. Heat cylinder head uniformly to a temperature of 80 to 100 °C 176 to 212 °F so that head will not be distorted, and drive new valve guide into hole with special tools. Shock absorber 5 Lower rear axle housing 2 gradually as far down as where coil spring 1 can be removed.

Next

Suzuki Jimny Sn413 1998

suzuki jimny sn413 2004 repair service manual

Tightening torque Brake back plate nuts a : 23 N·m 2. Special tool A : 09991-06040 3 Install O-ring 1 to compressor body assembly 2. Therefore, when using a new compres- sor for replacement, drain oil from new compressor by the amount calculated as follows. Studs If a broken stud is found, see Section 3E rear or Section 3D front for Note and Replacement procedure. Special tool A : 09917-68221 13 Remove crankshaft pulley 1.

Next

SUZUKI JIMNY SN413 WORKSHOP SERVICE REPAIR MANUAL

suzuki jimny sn413 2004 repair service manual

Generally, the only adjustment required for front wheel alignment is toe setting. Always replace both upper and lower inserts as a unit. Intermittent trouble or Go to Step 4. See below for a list of items that most of our manuals cover. Shoe hold down pin 2.

Next

DOWNLOAD SUZUKI SERVICE MANUAL: SUZUKI JIMNY SN413 WORKSHOP SERVICE REPAIR MANUAL

suzuki jimny sn413 2004 repair service manual

Condenser outlet pipe: Apply compressor oil to O-ring. Tightening torque Vacuum pipe clamp bolts a : 5. If any defect is found, replace pump assembly. Apply sealant to thread parts of breathing plug and tighten breath- ing plug to specified torque. If, any clogs are found, condenser fins should be washed with water, and should be dried with compressed air. Replace with new one if defective.

Next

Suzuki Jimny Workshop & Owners Manual

suzuki jimny sn413 2004 repair service manual

If it is hard to remove, use special tools as shown in figure. Poor contact of shoes on brake drum Repair for proper contact. They must be replaced with one of the same part number or with an equivalent part if replacement becomes necessary. It consists of the parts as described below and has an electronic ignition control system. Brake warning light Bulb burnt out Replace bulb. A light may be needed in some poorly-lit areas.

Next